Parbury Building Products - Wilsonart: Metals (Types 401, 416, 418, 419 And 420)

1. Distributor	2. Manufacturer

Parbury FHS. 166-168 Newton Road Wetherill Park NSW 2164 Phone: (0061) 2 98289622. Fax: (0061) 2 98289677. Email: parbury@parbuild.com.au Web Site: www.parbuild.com.au	Wilsonart International 2400 Wilson Place P.O. Box 6110 Temple, Texas 76503-6110 Phone: (254) 207-7000; (800) 433-3222 Fax: (254) 207-2384 Web Site: www.wilsonart.com

Recommended Uses: Wilsonart Decorative Metals are designed for vertical interior or ceiling applications where a special accent is required or a special mood is desired. The surface of Decorative Metals is that of fine finished metal. The genuine metal material is appropriate for vertical areas in hotel and office lobbies, theaters and restaurants, where its special eye-catching properties add a definite prestigious appeal. Decorative Metals add a visual sense of lightness when used as inserted accent banding in massive casework. These materials also can add a bright touch when used as accent trim in custom furniture, especially in combination with high gloss solid colour laminates, Wilsonart® Custom Edges or Wilsonart® Gibraltar® Solid Surfacing.

A-Look Mirror Quality Decorative Metals are shatterproof, lightweight and unbreakable. Non-distorted mirror reflective qualities make A-Look Decorative Metals perfect for ceilings, walls, columns, safety mirrors and display cases. A-Look EX is recommended for exterior and high humidity areas.

Basic Limitations: All decorative metals are designed for interior applications. Only A-Look Mirror Metals with an "EX" designation are recommended for exterior applications. Reflective value and metal colour may vary depending on type of lighting used. Fluorescent, incandescent and daylight produce slight colour variations.

Note: All decorative metals are supplied with a protective peel coat to prevent surface damage.

Sheet Dimensions

Type 401

Sheet Width 48" (-0 + 1/4") 1219.2mm (-0 + 6.350mm)

Sheet Lengths 96" (-0 + 1/2") 2438.4mm (-0 + 12.700mm)

2438.4mm (-0 + 12.700mm) 3048 mm (-0 + 12.700mm)

Sheet Thicknesses 0.079" (2mm)

0.118" (3mm)

Type 416

Sheet Width 24" (-0 + ¼") 609.6mm (-0 + 6.350mm)

Sheet Lengths 96" (-0 + ½") 2438.4mm (-0 + 12.700mm)

120" (-0 + ½") 3048.0mm (-0 + 12.700mm)

Sheet Thickness 0.025" ± 0.002" (0.635mm ± (0.050mm)

Edge Trim 1 3/4" x 120" (44.450mm x 3048mm)

Type 418

Sheet Width 24" (-0 + 1/4") 609.6mm (-0 + 6.350mm)

48" (-0 + 1/4") 1219.2mm (-0 + 6.350mm)

Sheet Lengths 96" (-0 + 1/2") 2438.4mm (-0 + 12.700mm)

120" (-0 + 1/2") 3048.0mm (-0 + 12.700mm)

Sheet Thicknesses 0.046"± 0.004" (1.16mm ± 0.101mm)

Type 419

Sheet Width 24" (-0 + 1/4") 609.6mm (-0 + 6.350mm)

48" (-0 + 1/2") 1219.2mm (-0 + 12.700mm)

Sheet Lengths 96" (-0 + 1/2") 2438.4mm (-0 + 12.700mm)

120" (-0 + 1/2") 3048.0mm (-0 + 12.700mm)

Sheet Thickness 0.025" ± 0.002" (0.635mm ± 0.050mm)

#6277 AlumaSteel™ 0.030" ± 0.002" (0.762mm ± 0.050mm)

Edge Trim 1 ¾" x 120" (44.450mm x 3048mm)

Type 420

Sheet Width 24" (-0 + 1/4") 609.6mm (-0 + 6.350mm)

Sheet Length 120" (-0 + 1/2") 3048mm (-0 + 12.700mm)

Sheet Thicknesses 0.020" ± 0.003" (0.508mm ± 0.076mm)

Edge Trim 1 3/4" x 120" (44.450mm x 3048mm)

Codes and Certifications: Currently there are no NEMA standards or tests for decorative metal surfacing. However, American National Standards Institute/National Electrical Manufacturers Association (ANSI/NEMA), LD3-1995 should be consulted for basic fabrication and handling techniques.

A-Look Mirror Quality Decorative Metals have been tested in accordance with ASTM-E84, Tunnel Test, and achieved Class 1 or A as follows:

Aviation: Federal Aviation Administration, Transport Category Airplanes, Paragraph 25.853(a) and Appendix F, Part 1, Paragraph (a) (1) (IV), Vertical Test as published in the Federal Register and Amendment 250-74, effective May 16, 1991.

General Standards: Currently there are no NEMA standards or tests for decorative metal surfacing.

Specific Product Standards: Currently there are no NEMA standards or tests for decorative metal surfacing.

For comprehensive fabrication instructions for Metal types 416, 418, 419 and 420, consult the Decorative Metals Fabrication Manual, BR0405.

Fabrication and installation of A-Look Mirror Quality Decorative Metals is easy with tools and machinery normally associated with laminate, metal or woodworking shops. A fabrication manual is available upon request. They are easily applied by using a low- or non-shrink silicone sealant and low-modulus contact cement, or a very high-bond type of double-stick foam tape. Please refer to the manual for comparison to other reflective mirror materials for equivalent rigidity and general properties.

Some points to keep in mind when using A-Look Decorative Metals include:1. Use on vertical surfaces only. Horizontal work surfaces are not recommended.2. A-Look Decorative Metals can be formed using standard roll bending equipment. *3. The protective film should be removed as soon as the application is complete. If the film is left in place after fabrication, exposure to direct sunlight for a prolonged period may cause a paste residue and create other problems.4. For exterior applications, the edge of A-Look EX Decorative Metals should be covered or sealed with aluminum or stainless steel molding (such as H or J mold) using a sealant that does not contain acid or a strong alkaline solution. Interior applications can be butt jointed.Caution: Check adhesive carefully prior to application. When adhesive is used, due to the inherent thermal expansion and contraction ratios, A-Look Decorative Metals may pull toward the base material after installation. It is suggested that you use VHB double-stick foam tape, or a low-modulus silicone or rubberizing contact cement.*Please refer to the A-Look Fabrication Manual (BR410) for complete fabrication details.

Wilsonart International Inc., the distributor of this decorative metal product, makes no warranty of any kind, express or implied, but not limited to any warranties of merchantability or fitness for a particular purpose with respect to the customer's intended use of this decorative metal product. Under no circumstances shall Wilsonart International Inc. be liable for any loss or damage arising from the purchase, use, or inability to use this product, or for any special, indirect, incidental or consequential damages. No fabricator, installer, dealer, agent or employee of Wilsonart International Inc. has the authority to modify the obligations or limitations of this warranty.

This limitation of liability gives you specific legal rights. You may have other rights that may vary from state to state. Some states do not allow the exclusion of implied warranties or of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

For samples, literature, questions or technical assistance, please contact our toll-free Hotline at (Australia) 1300 361 313 or (New Zealand) 0800 657 774, Monday through Friday, 8 am - 5 pm.

Surface shall be Wilsonart Decorative Metals,

Type: Specify 401, 416, 418, 419 or 420

Surface

Metal Number: __________

Metal Name: __________

Adhesive

Name: __________

Grade/Type: __________

Manufacturer: _______________

Fabrication shall comply with Architectural Woodwork Quality Standards, Guide